出版日期: 1999-10-01
本规程适用于汽轮发电机组为125MW 及以上新建或扩建的凝汽式发电厂的设计以及高温高压及以上参数供热式机组的热电厂设计,安装上述机组的发电厂改建工程的设计可参照使用。
涉外工程可根据实际情况参照使用本规程。
Contents
Foreword
1 Scope
2 Normative Reference
3 General Provisions
4 Basic Provisions
4.1 Modular Coordination of Buildings
4.2 Fire and Explosion Protection
4.3 Noise Control
4.4 Lighting
4.5 Architectural Thermal Engineering and Energy Conservation
4.6 Building Construction
4.7 Buildings and Seismic Resistance
5 Main Plant Buildings
5.1 Main Building
5.2 Centralized Control Building
6 Electrical Buildings
6.1 Main Control Building (Network Control Building)
6.2 Communication Room (Building)
6.3 Electrical Laboratory
6.4 Distribution Equipment Building
7 Fuel and Dedusting Building
7.1 Slot Coal Chute
7.2 Tippler Room
7.3 Dry Coal Shed
7.4 Coalbreaker Room and Transfer Station
7.5 Coal Delivering Trestle and Tunnel
7.6 Coal Shipment Comprehensive Building
7.7 Coal Transporter Bin
7.8 Fuel Pump Room
7.9 Dedusting Building
8 Chemical Buildings
8.1 Boiler Feedwater Processing Room
8.2 Circulating Water Processing Room
8.3 Acid and Alkali Unloading Station
8.4 Oil Purification Room
8.5 Hydrogen Generator Station
9 Subsidiary Buildings
9.1 Repair Plant
9.2 Air Compressor Room
9.3 Environmental Laboratory
9.4 Thermal Engineering Laboratory
9.5 Metal Laboratory
9.6 Partial Field Maintenance Room
10 Auxiliary Buildings
10.1 Office Building, Training Room and Simulator Room
10.2 Security Room and Janitor Room
10.3 Material Warehouse
10.4 Garage
10.5 Fire House
11 Living Building in Plant
11.1 Canteen
11.2 Dormitory Duty Building
11.3 Hotel and Maintenance Dormitory
11.4 Nursery and Infant School
11.5 Athletic and Recreational Buildings
11.6 Bathroom
11.7 Other Living Buildings
Annex A
Annex B
Annex C
Annex D
Annex E
1 Scope
This code is applicable to the design of the newly-built or extended 125 MW and above turbogenerator set condensing power plants and the design of HTHP and above heating set heat power plants, and it may also be used as reference for the design of power plant reconstruction engineering that is installed with aforementioned sets. Besides, this code may be applied for reference in foreign engineering according to the practical situations.
2 Normative Reference
The following standards contain provisions which, through reference in this text, constitute provisions of this code. At time of publication, the editions indicated were valid. All standards are subject to revision, and parties to agreements based on this code are encouraged to investigate the possibility of applying the most recent editions of the standards indicated below.
GB 50033-1997 "Standard for Lighting Design of Buildings"
GB 50037-1996 "Code for Design of Ground Surface and Floor of Building"
GB 50045-1995 "Code for Fire Protection Design of Tall Building"
GB 50176-1993 "Thermal Design Code for Civil Building"
GB 50177-1993 "Design Code for Hydrogen and Oxygen Station"
GB 50207-1994 "Technical Code for Roof Engineering"
GB 50222-1995 "Code for Fire Prevention in Design of Interior Decoration of Buildings"
GB 50229-1996 "Code for Fire--protection Design Power Plant and Substation"
GBJ 2-1986 "Building Constructions--Modular Coordination--Unified Standards"
GBJ 6-1986 "Building Constructions-Modular Coordination-Standards for Factory Buildings"
GBJ 11-1989 "Code for Seismic Design of Buildings"
GBJ 16-1987 "Code of Design on Building Fire Protection and Prevention" (Revision)
GBJ 67-1984 "Specifications for the Design of Garages-fire Prevention"
GBJ 87-1985 "Code for Design of Noise Control in Industrial Enterprises"
GBJ 101-1987 "Building Construction-Modular Coordination-Stairs"
GNJ 1-1981 "Standard for Architectural Design of Fire Stations"
JGJ 26-1995 "Energy Conservation Design Standard for New Heating Residential Buildings"
JGJ 36-1987 "Code for Design of Dormitory Building"
JGJ 37-1987 "Code for Design of Civil Buildings"
JGJ 39-1987 "Code for Design of Nursery and Infant School Buildings"
JGJ 64-1989 "Code for Design of Dietetic Buildings"
JGJ 67-1989 "Code for Design of Office Buildings"